The short answer

An old Brinks alarm that beeps every 24 hours has a low backup battery or a dead phone-line connection; press CANCEL to silence it, enter your code + OFF to clear it, or unplug the transformer and battery to stop it for good. Independent help at (888) 207-7106.

An old Brinks alarm that beeps every fifteen seconds, or wakes you once a day, has a trouble condition - almost always a worn backup battery or a failed phone-line connection to a monitoring centre that may no longer be listening. Pressing CANCEL on the keypad silences it for 24 hours, which is why it feels like it "beeps every 24 hours". Enter your code and press OFF to clear it properly; if it comes back, the sections below tell you what to fix and whether it's worth fixing.

First, who are you dealing with? There are two completely different "Brinks":

  • The original Brinks Home Security (1983-2009) - grey or beige keypads marked BRINKS with a two-character display, panels labelled BHS-1200, BHS-2000, BHS-3000, BHS-4000 and the DCU-500 keypad. Brinks spun this off as Broadview Security in 2009, and ADT bought Broadview in 2010. If yours is still monitored, it's monitored by ADT. This guide is about these systems.
  • Today's Brinks Home (2018 onward) - the former Monitronics / MONI, with white touchscreens (Qolsys IQ Panel) or 2GIG panels and an Alarm.com app. Different company, different equipment: see the IQ Panel guide or the 2GIG panel guide.

Who to call - two different numbers for two different jobs

Still paying for monitoring on an old Brinks system?
ADT (owns the old Brinks/Broadview accounts): 1-800-238-2727
Brinks Home (today's company, ex-Monitronics): 1-800-447-9239
Their own lines. We are neither company. Old Brinks accounts almost always ended up at ADT.
Independent help (not Brinks or ADT): nobody monitors it, parts don't exist, and it won't shut up?
CompareYourSecurity specialists: ☎ (888) 207-7106
Free second opinion on silencing it for good, re-using the wired sensors on a new panel, or what a replacement should really cost.

This is an independent guide - we are not Brinks, Broadview, ADT or any alarm manufacturer. If you want a straight answer rather than reading on: ☎ (888) 207-7106 or the free 60-second assessment.

What the display means: CP trouble, CH trouble, bAt, AC and the beeping patterns

Stuck after these steps? Independent help (not Brinks or ADT): ☎ (888) 207-7106

Close-up of a dated grey alarm keypad by a front door with a small two-character display lit and a trouble light on

Brinks keypads from the 1990s and 2000s have a tiny two-character display and a row of lights rather than words. The system beeps every 15 seconds for a new trouble; pressing CANCEL quiets it for 24 hours, after which it starts again if the trouble is still there. The codes owners ask about most:

  • CP - a control panel trouble: the panel is reporting a problem with itself rather than a zone. On Brinks systems this is most often the backup battery (worn out or disconnected) or a communication failure - the panel can't reach the monitoring centre over the phone line. If you no longer have a landline, or no longer have monitoring, CP is what you'd expect to see permanently.
  • CH - a check condition on a zone or device: a door or window sensor the panel can't verify (magnet misaligned, wire broken, wireless sensor battery dead), or a tamper. The zone number usually follows or alternates with CH.
  • bA / bAt / "LOW BAT" light - the panel's 12 V backup battery is low. After a power cut, allow 24 hours to recharge; if the trouble stays, the battery is finished.
  • AC / "AC" light off - the panel has lost mains power: transformer unplugged, outlet dead, or the panel's fuse.
  • FC / "COMM FAIL" (some models) - failure to communicate. The panel dialled the monitoring centre and nothing answered - no dial tone, a VoIP line it can't talk through, or a receiver that no longer exists for this account.
  • Numbers 01-99 - a zone. With the TROUBLE light on, that zone has a fault; with the ALARM light on, it was the zone that caused the last alarm.

Exact code sets differ between the BHS-2000, BHS-3000 and BHS-4000 panels and the keypads fitted to them, and Brinks dealers used several keypad versions. If your display shows something not listed here, note the pattern (which lights are on, what the two characters are) - a technician or an independent specialist can usually place it from that.

Not sure which system you need?

Answer a few quick questions and we'll match you with a top-rated provider for a free, no-obligation quote — or compare our top picks yourself.

How to turn off an old Brinks alarm (silence, reset, and power down for good)

Stuck after these steps? Independent help (not Brinks or ADT): ☎ (888) 207-7106

Silence a trouble beep: press CANCEL (quiets for 24 hours), or enter your 4-digit code then OFF. The trouble light stays on until the cause is fixed.

Stop a full alarm (siren): code + OFF. If the keypad ignores the code or the display is dead, go to the panel.

Reset after fixing something: code + OFF, twice. On some Brinks keypads you then press CANCEL once to clear the trouble memory. If the display still shows the code, the fault is still present.

Turn it off without a code / for good:

  1. Find the panel - a beige or grey metal box, about the size of a shoebox, in a closet, basement, utility room or garage, often with a Brinks sticker.
  2. Unplug the transformer - a plug-in block, usually at an outlet near the box, sometimes screwed to the outlet plate.
  3. Open the box (a screw or a key - the key is usually long gone; the screw heads take a flat or Phillips driver) and pull the red lead off the battery, then the black.
  4. Everything stops within seconds. The sensors and keypad are now dead. Nothing is erased; reconnect battery then transformer and it comes back exactly as it was.

If you're decommissioning the system, take the battery to a recycling point (lead-acid). Leaving the panel powered with no monitoring and a dying battery is what produces the once-a-day 2 a.m. beep people live with for years - unplugging it is the cure. If you'd like the siren to keep working locally without the trouble beeps, that needs the installer code, which Brinks dealers rarely left behind; a takeover company can usually get into a BHS panel, or you can swap the board for a modern one that re-uses the wired sensors - see below.

Get matched with a top provider

Old Brinks alarm battery replacement

Stuck after these steps? Independent help (not Brinks or ADT): ☎ (888) 207-7106

Open beige metal alarm control box in a basement with a small rectangular 12-volt battery and red and black leads

Brinks panels take the same battery as almost every wired alarm of their era: a 12 V sealed lead-acid, 4 Ah or 5 Ah, about 3.5 × 2.75 × 4 inches, with two 0.187-inch spade terminals. Universal part - any brand marked 12V 4Ah or 12V 5Ah with F1 terminals fits ($15-$25 at hardware stores, battery shops or online). They last 3-5 years; the one in your Brinks box may be 15.

  1. Disarm. If the system is still monitored, put it on test with ADT first (1-800-238-2727) - opening the box trips the tamper.
  2. Unplug the transformer so the panel is fully powered down (optional but safest).
  3. Open the box. Pull the red lead off the battery, then the black.
  4. Lift the old battery out, put the new one in, connect black first, then red.
  5. Plug the transformer back in, close the box. The low-battery trouble can take up to 24 hours to clear while the new battery charges; press code + OFF twice to clear the memory afterwards.

Battery is new and the beeping continues? Then the trouble was never the battery - it's communication (the panel has nobody to call), a zone, or the panel's charging circuit. On a system this age that's the point to ask whether more money should go in. Wireless Brinks sensors (the few systems that had them) take a 3 V lithium cell or 9 V battery inside the sensor; open the cover and read it.

Is an old Brinks system worth keeping? Your three options

Stuck after these steps? Independent help (not Brinks or ADT): ☎ (888) 207-7106

Nobody makes BHS panels or parts any more, and the system was built to dial a phone line most houses no longer have. But the expensive part of any alarm - the wired door, window, motion and smoke sensors running through your walls - is still perfectly good. That shapes the choices:

OptionWhat it involvesTypical costBest when
Keep it monitored with ADTADT services old Brinks/Broadview accounts; they'll replace the battery and may add a cellular communicator so it stops needing a phone line.Service call $59-$99; communicator $150-$250 or a new contractYou already pay ADT and the panel otherwise works.
Swap the board, keep the wiringAn independent company removes the Brinks board and fits a modern panel (Honeywell Vista, DSC PowerSeries, Qolsys with a hardwire translator) in the same box, re-using every wired sensor. New keypad, LTE, app.$300-$600 installed; $15-$30/month monitoring, often no contractYou want real monitoring without ADT's pricing. The most common path.
Retire itUnplug transformer and battery; leave the sensors in the walls for a future takeover or go DIY wireless.$0You don't want monitoring and just want the beeping gone.

The trap: a "free upgrade" from any company that replaces your perfectly good wired sensors with wireless ones and ties you to a 36-60-month contract at $45-$60 a month. The sensors in your walls are worth keeping; the contract usually isn't. Get the board-swap price from an independent first. Need the maths for your house? Alarm system repair: fix or replace, or one call to an independent specialist who doesn't sell either option: ☎ (888) 207-7106. If ADT is who you pay and you're unhappy, how to cancel ADT without the fee covers the contract side.

Frequently asked questions

Why does my old Brinks alarm beep every 24 hours?

It has a trouble condition - usually a worn backup battery or a failed phone-line connection - and pressing CANCEL silences it for exactly 24 hours. Enter your code and press OFF to clear it; fix the cause or it returns. Still stuck after that? Independent help (not the alarm company) is at (888) 207-7106.

What does CP trouble mean on a Brinks alarm?

A control-panel trouble: the panel is reporting a problem with itself, most often a low or disconnected backup battery or a failure to communicate with the monitoring centre over the phone line. Still stuck after that? Independent help (not the alarm company) is at (888) 207-7106.

What does CH trouble mean on a Brinks alarm?

A check condition on a zone or device - a door or window sensor the panel can't verify, a broken wire, a misaligned magnet, or a tamper. The zone number usually shows with it.

How do I turn off an old Brinks alarm system?

Enter your 4-digit code and press OFF. To shut it down completely, unplug the transformer at the outlet and disconnect the red then black battery leads inside the metal panel box. Nothing is erased.

What battery does a Brinks home security system use?

A universal 12 V 4 Ah or 5 Ah sealed lead-acid battery with F1 spade terminals, $15-$25. Connect black first, then red; the low-battery trouble clears within 24 hours.

Who monitors old Brinks Home Security systems now?

ADT. Brinks Home Security became Broadview Security in 2009 and ADT acquired Broadview in 2010. Today's "Brinks Home" is the former Monitronics and is a different company with different equipment.

Is Brinks Home Security still in business?

The original Brinks Home Security is not - it became Broadview and was absorbed into ADT in 2010. The Brinks Home that exists today is Monitronics, which licensed the Brinks name in 2018.

Can I reuse my old Brinks sensors with a new system?

Yes. The wired door, window, motion and smoke sensors work with any modern hardwired panel (Honeywell Vista, DSC) or with a wireless panel via a hardwire translator. Only the Brinks board and keypad need replacing.

How do I stop a home alarm from beeping?

Enter your code and press OFF (or Disarm), twice if the first press only silences. If the beep returns within hours it's a trouble - battery, power or communication - and the keypad's display or lights tell you which. With no code, unplug the transformer and disconnect the panel battery.

What is the Brinks home security box in my closet?

The metal control panel - the system's brain, battery and phone-line connection. Keypads by the doors are just displays wired to it. Everything in this guide about batteries and powering down happens inside that box.

Does the old Brinks system have a doorbell camera or app?

No. Original Brinks Home Security systems pre-date cameras and apps. The Brinks doorbell camera and Brinks Home app belong to today's Brinks Home (ex-Monitronics), which uses Qolsys IQ panels - see the IQ Panel guide.

Are old home security systems worth keeping?

The wired sensors are; the 1990s-2000s control board and dial-up communicator usually aren't. Troubleshooting an old alarm system past a battery swap rarely pays - a board swap that re-uses the wiring is the cost-effective middle ground.

Why does the alarm keypad beep but show nothing?

On older Brinks keypads a trouble beep with a dark or blank display means the keypad has lost power or data from the panel - a broken wire, a failed keypad, or the panel itself shutting down on a dead battery. Check the panel's AC and battery first.

CompareYourSecurity.com is an independent reviews site and is not affiliated with Brinks, Broadview, ADT or Monitronics. Display codes and key sequences vary by panel and keypad model and by dealer programming. Put a monitored system on test before opening the panel. In an emergency, call 911.

Still stuck? Our independent specialists are at ☎ (888) 207-7106, or start with the free assessment.